Close
0%
0%

MAX7000S CPLD JTAG Tester

A simple JTAG test board for 84pin PLCC MAX7000S CPLD

tomcircuittomcircuit
Following
Liked Like project

Just one more thing

To make the experience fit your profile, pick a username and tell us what interests you.

Pick an awesome username
hackaday.io/
Your profile's URL: hackaday.io/username. Max 25 alphanumeric characters.
Pick a few interests
Projects that share your interests
People that share your interests

We found and based on your interests.

Choose more interests.

OK, I'm done! Skip
Similar projects worth following
299 views
1 comments
2 followers
View Gallery
I am a big fan of the EPM7128SLC84 CPLD device. It supports 5V I/O for retroputing projects,
has enough macrocells to support medium complexity projects (e.g. glue for hd6309 SBC), etc.
This device is EOL from Altera (Intel) but can be found on the 'gray-market' (e.g. eBay).
However, many of the devices found from such sellers are not usable because the JTAG pins
have been re-assigned to I/O. Once this is done, the CPLD can only be reset to factory
default state with hard-to-find Altera parallel programming equipment.

So, this project was born to allow CPLD devices to be temporarily connected to an Altera USB
blaster (or compatible) to see if the JTAG is operational. A 3M PLCC socket is used for this
project, which might be a bit hard to find, but is well worth the effort.

This is about as simple as it gets! A rudimentary 5V supply is included onboard for ease of use. A "current" header is included, to allow the CPLD IDD to be measured - this is another good way to determine if your unknown CPLD is good/bad. The obligatory LED is included (yes, that current is drawn through the shunt connector as well!). A 10 pin JTAG header allows connection to the USB blaster, and the 84pin PLCC test socket is where the D.U.T. goes. 

MAX7128_JTAG_Tester_Schematic.pdf

Adobe Portable Document Format - 83.60 kB - 02/06/2020 at 18:45

Preview

  • Built and Working

    tomcircuit • 02/06/2020 at 19:02 • 0 comments

    I built up the board (well, all but the regulator, which I'm still waiting on...) and fired it up by injecting the 5V through the "current" header. I was able to sort through about a dozen or so EPM7128SLC84 and even a few EPM7160SLC84 devices.  All from eBay, and 5/12 had locked-out JTAG :-(  But, better to learn this now, instead of after being soldered onto my project PCB!

View project log

Enjoy this project?

Share

Discussions

error_4o4 wrote 03/26/2021 at 12:51 • point

I don't see the +12V Vpp on this design. Do I miss something? I had to apply it to some devices with locked JTAG to reenable the JTAG interface so I can use the device again..

  Are you sure? yes | no

Similar Projects

Every Day Carry bit flipper
Project Owner Contributor

Tiny Bit Dingus

ajlittajlitt

To go anywhere you have to leave somewhere else
Project Owner Contributor

Skype 'kiss' interface

nathanNathan

The device tests for continuity and internal resistors within various USB Cables and exposes some pins for multimeter testing.
Project Owner Contributor

USB Sleuth Cable Tester

spencer-maroukisSpencer Maroukis

Miniature dev board for SAM21D / SAM20D ARM cortex M0+
Project Owner Contributor

mini SAM

alexAlex

Does this project spark your interest?

Become a member to follow this project and never miss any updates

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday

Yes, delete it Cancel

Report project as inappropriate

You are about to report the project "MAX7000S CPLD JTAG Tester", please tell us the reason.

Send message

Your application has been submitted.

Remove Member

Are you sure you want to remove yourself as a member for this project?

Project owner will be notified upon removal.