Close
0%
0%

Gregor

Industrial designer

Den Haag
Following
Send a private message
Similar accounts worth following
2 Followers
2 Following
4 Projects
13 Likes
gregor
Send a private message

This user joined on 07/08/2014.

530
5
2
5
A coin-cell powered ATTiny board with popular peripherals (USB, potmeter, slide/tact switch, piezo buzzer, LED) to jump-start tiny projects.
Project Owner Contributor

Duinothrowie

gregorGregor

2.6k
2
1
5
Refurbishing a behemoth of an industrial 3D-printer to working condition after it has been left for dead in the shed of a big company
Project Owner Contributor

Stratasys Dimension SST Extruder sensor repair

gregorGregor

1.1k
5
0
3
The Bus-powered RS485 Shield is an Arduino-compatible shield that allows full-duplex communication over long distances between 2+ Arduino's.
Project Owner Contributor

Arduino Bus-powered RS485 Shield

gregorGregor

0
0
0
Connect any shield to an Arduino with a flexible flat cable up to 50cm in length. Use an LCD screen with a button shield without blocking!
Project Owner Contributor

Arduino Flat Flexible Connector (FFC) Shield

gregorGregor

100.4k
1.4k
18
487
Affordable and open-source LiDAR based on 3x VL53L0X ranging sensor
Project Owner Contributor

xLiDAR

jrodrigoJRodrigo

61.7k
488
82
339
AMS's new AS7265X 3-chip set promises a compact, 18-channel, 20 nm FWMH spectrometer for less than $25
Project Owner Contributor

Compact, $25 spectrometer

kris-winerKris Winer

57k
428
71
319
Yet another Raspberry Pi Computer (non-official carrier board for CM4).
Project Owner Contributor

MirkoPC -> CM4 carrier board

mirkoMirko

30.7k
313
52
273
Small and powerfull controlling unit powerd from USB-C-PD
Project Owner Contributor

USB-C-PD Soldering Pen for Weller RT Tips

thomas-leputschThomas Leputsch

25.3k
162
22
189
... is designed for direct drive wheels for swarm robots
Project Owner Contributor

PCB stepper motor

bobriciusbobricius

24.8k
247
42
217
Extremely affordable pocket-friendly, designed to provide a wide range of hardware testing and debugging functions in a compact and low-cost
Project Owner Contributor

Felini - Revolutionary Pocket-Sized Electronic Lab

chu-tien-thinh-obitvnChu Tien Thinh (obitvn)

22.6k
136
21
114
Ultra low-cost controller for brushless servo based on the B-G431B-ESC1 Discovery kit by ST
Project Owner Contributor

B-G431B-ESC Brushless Servo Controller

pat92frpat92fr

19.8k
4k
48
107
A 3D printer for printing with welding wire
Project Owner Contributor

Wire 3D Printer

dominik-meffertDominik Meffert

18.3k
110
1
90
The ideal machine for recycling plastic bottles into 3D printer filament. Team Members: Reiten Cheng (Project Founder), Swaleh Owais
Project Owner Contributor

Polyformer - Ideal Filament Recycler

swaleh-owaisSwaleh Owais

11.4k
86
8
97
Kinetic sculptures based on Nautilus gears
Project Owner Contributor

Nautilus Sculptures

vipin-mVipin M

9.8k
28
13
31
.
Project Owner Contributor

Amazon Echo Show 10 3rd gen Teardown

txyzinfotxyz.info

9k
58
17
56
Test any electronic component with this pocket component tester
Project Owner Contributor

Component Tester in a Keychain

akshay-bawejaAkshay Baweja

8.9k
2.8k
23
78
Two hearts are better than one, so why not have five. Quadcore RPI CM4 and a MCU on a single board for true all-in-one 3D printer control.
Project Owner Contributor

Sigmoid S7P 3D Printer Control Board

pkelectronicspkElectronics

8.3k
69
10
61
Differential scope probe
Project Owner Contributor

PD150

craig-dCraig D

6.1k
2.6k
2
45
3D printed toroidally wound axial flux permanent magnet air core motor. 3DTAFPM?
Project Owner Contributor

3D Printed Axial Flux Motor

colby-johnsonColby Johnson

3.9k
41
2
40
This is a project where I built a sputtering magnetron to deposit thin conductive films on surfaces.
Project Owner Contributor

Sputtering Magnetron

steve-hernandezSteve Hernandez

3.6k
26
14
33
The Ultra-Compact Powerhouse for LoRa Debugging and Connectivity
Project Owner Contributor

LoShark

reimu-notmoeReimu NotMoe

2.2k
33
2
22
Using your phone’s camera and IMU to position stabilize a self balance robot – no additional sensors needed
Project Owner Contributor

World’s first camera stabilized self balance robot

serialsensorSerialSensor

View all

Share this profile

Share

Bits

Kris Winer wrote 06/13/2018 at 15:29 • point

Thanks for following my $25 Spectrometer project!

  Are you sure? yes | no

Send a private message to Gregor

Become cool instantly

Create your Hackaday.io profile like Gregor and many others

By using our website and services, you expressly agree to the placement of our performance, functionality, and advertising cookies. Learn More

Report user as inappropriate

You are about to report the user "Gregor", please tell us the reason.