Close
0%
0%

Automatic Sanitiser Dispenser

Dispenses few ml of liquid sanitiser with the help of submersible motor on sensing hand (obstacle detection) using IR module

tusharTushar
Following
Liked Like project

Just one more thing

To make the experience fit your profile, pick a username and tell us what interests you.

Pick an awesome username
hackaday.io/
Your profile's URL: hackaday.io/username. Max 25 alphanumeric characters.
Pick a few interests
Projects that share your interests
People that share your interests

We found and based on your interests.

Choose more interests.

OK, I'm done! Skip
Similar projects worth following
256 views
3 comments
1 followers
View Gallery
This project allows the user to get sanitiser without touching any part of the sanitiser bottle or any buttons. It dispenses few ml of liquid sanitiser with the help of submersible motor on sensing hand (obstacle detection) using IR module.

Important points about the project :
-----------------------------------------------------
1. IR module is used to detect hand
2. A submersible DC motor pump (5V, 180mA) is used to pump the sanitiser.
3. Arduino UNO board is used to control the dispenser.
4. ULN 2003A module is used to drive the DC motor.
5. Two IR modules are provided to avoid unintentional trigger. However, I ended up using only one.

Current Status
---------------------
This project is working fine with water. I have ordered a plastic container to hold the sanitiser.
I am planning to use the copper straw as a tube to dispense the sanitiser. I will upload more pics once the entire unit is ready. Also plan to miniaturise it in the future.

ASD_ATTiny85.ino

Code for ATTiny85 Based ASD Implementation

x-arduino - 2.96 kB - 08/02/2020 at 02:34

Download

AutoSanDispenser.ino

Arduino Uno Sketch For Automatic Sanitiser Dispenser

x-arduino - 3.42 kB - 07/09/2020 at 20:41

Download

  • 1 × Arduino Uno Board Microcontroller Development Board
  • 1 × ULN2003A Module DC Motor Driver
  • 2 × IR Module IR Transmitter & IR Receiver with on board LM393 comparator (with sensitivity adjustment). Only 1 is mandatory. The second sensor module is optional.
  • 1 × Small Breadboard
  • 1 × Wires

View all 10 components

Enjoy this project?

Share

Discussions

Martin wrote 07/13/2020 at 08:41 • point

Why did you use the 7 channel ULN2003 for the motor? For just one motor with single direction operation  a simple small NPN transistor or MOSFET ( with a resistor or 2) is enough.

  Are you sure? yes | no

Tushar wrote 07/13/2020 at 09:27 • point

You are right Martin. However, I had these modules available and they just had to be connected with wires (no soldering). So used it temporarily just to see it work. I am planning to reduce this circuit by using ATTiny85, connect IR LEDS to micro directly and use internal comparator / ADC & an external transistor to switch the motor. Thanks for your suggestion though. Keep providing your inputs.

  Are you sure? yes | no

Similar Projects

My project uses X-ray microfocus radiography to monitor the changing displacement patterns and saturations of Berea sandstone rock samples w
Project Owner Contributor

The Use of Foam As a Mobility Control Agent for Co

mark-liuMark Liu

As the nor'easter rages, I made a enhanced tank to trail though the snow and heavy winds.
Project Owner Contributor

Makeblock Robot Tank Enhanced

ricardo-ferroRicardo Ferro

updating a 1968, 3 cylinder, 55 hp, johnson outboard motor with junkyard parts to have crank triggered distributorless ignition.
Project Owner Contributor

Boat Motor Gets Updated Ignition

duane-grzybDuane Grzyb

In this project we will turn on and off using two forms of communication: manually and through radio frequency that has a range of approxi..
Project Owner Contributor

DIRECT START (RF – MANUAL)

electronicabcElectronicABC

Does this project spark your interest?

Become a member to follow this project and never miss any updates

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday

Yes, delete it Cancel

Report project as inappropriate

You are about to report the project "Automatic Sanitiser Dispenser", please tell us the reason.

Send message

Your application has been submitted.

Remove Member

Are you sure you want to remove yourself as a member for this project?

Project owner will be notified upon removal.