Project Logs

Collapse

• Serial OutPut of the project

  Rfiles • 08/28/2022 at 20:06 • 0 comments

  This Appears messy because of wrong font. Must be a fixed lenght.

  Aug 28 2022 16:57:561
  Station_07 Loader of 18 Modules:
  Primary I2C Scan
   Got = 23  38  39  70  
  Primary I2C Scan Done
  TCA I2C Scan
   Port 0 Got = 00 20 48
   Port 1 Got = 5A
   Port 2 Got = 10 29 68 76
   Port 3 Got = 23 38 39
   Port 4 Got =
   Port 5 Got =
   Port 6 Got = 00 40 5A 60 76
   Port 7 Got = 29
  TCA I2C Scan Done
   00: SCN S[  23] D[158] OK
   01: RAM S[ 181] D[  1] OK
   02: SI7 S[ 182] D[ 53] OK
   03: BME S[ 235] D[123] OK
   04: ADS S[ 358] D[  0] OK
   05: MCP S[ 358] D[ 10] OK
   06: CCS S[ 368] D[204] OK
   07: MIC S[ 572] D[  0] OK
   08: SI1 S[ 572] D[ 52] OK
  E (626) gpio: gpio_set_level(226): GPIO output gpio_num error
  E (636) gpio: gpio_set_level(226): GPIO output gpio_num error
   09: VL5 S[ 624] D[ 72] OK
   10: TCS S[ 696] D[620] OK
   11: MLX S[1316] D[  1] OK
   12: BH1 S[1317] D[ 20] OK
   13: MPU S[1337] D[639] OK
   14: VE0 S[1976] D[  4] OK
   15: BMP S[1980] D[108] OK
   16: VL0 S[2088] D[2001] OK
   17: WS2 S[4089] D[  1] OK
  Load Done
  RAM: Total 0528 regs of 0248 bytes each.
  Starting Timed Tasks

  NOC: 000017   TOC: 000046   TIM: 01:00:49
  BME: T[29.43] P[1005.826] H[45.10] 
  BMP: T[30.22] P[1005.495]
  SI7: T[29.46] H[43.67] 
  CCS: eCO2[ 428] VOL[   4] 
  ADS: 1[  131] 2[ 1348] 3[   71] 4[17477](3.29V)
  MIC: Carb Mono[3.19]  Diox Nitr[0.15]  Amonio[0.18] Propano[74.27]
  MIC: Butano[70.54] Metano[194.24] Hidrog[0.45] Etanol[1.07]
  MCP: IN(A)[###-##-#] OUT(B)[--------] Int[--------](0)(0) 
  BH1: Lux[41.67]
  SI1: VIS[  261] IR[  261] UV[    0] PROX[  255]
  TCS1: R[ 3467] G[ 3443] B[ 3588] C[ 7978] IR[ 1260]
  TCS2: C_R[ 2207] C_G[ 2183] C_B[ 2328] R_C[ 6718] LUX[48.95]
  TCS3: CR[0.16] AGX[   60] ATMS[  153] CPL[29.61]
  TCS4: MAX_LUX[737.69] K[5409.89]
  VE5: UVA[0.00] UVB[0.00] UVI[0.00]
  VE0: UVI[0]
  VL5: Distance [1739] mm
  MLX: Amb[26.93] Obj[25.91]
  MPU: Ax[0.00] Ay[0.00] Az[1.01] - Gx[0.01] Gy[-0.05] Gz[0.02]
  MPU: Mx[30.29] My[110.58] Mz[229.36] SumG[1.01] T[36.58'C]
  MPU: ANx[0.01] ANy[0.05] ANz[90.00] Pitch[-0.01] Roll[0.03] M[0]

• This is the Tasks That Run Periodicaly

  Rfiles • 08/28/2022 at 20:03 • 0 comments

  Timers:

  Number	Time in ms	Description
  0	500	MCP23017 Port B1 Led Blink
  1	2500	Get And Store All Sensors Data
  2	1234	Process Values. NOT USED
  3	5000	List All Sensors Data in Terminal
  4	5000	Send All Sensors Data to MQTT Server

• Commands That I Created

  Rfiles • 08/28/2022 at 20:02 • 0 comments

  Commands:

  Command	Description
  0	Force Listing of stored Values
  1	Force Gather Values from Sensors
  e	Force Boot Modules
  s	Execute Create Timers Function
  g	Start / Stop Timers (g <Timer #> on/off )
  r	Force Send Data to Influx Database (Does Not Word)
  i	Force Send Sensors Data to MQTT server (Nodered in my case)
  o	Connect to configured WIFI network
  w	Sync with NTP server and Show Clock
  h	Toggle MCP23017 Pin (h <pin # in port B> [optional 1/0, default is 1]
  j	Set Si1145 Led Current (j <0..15>) Its from 1mA to 300mA
  p	Set WS2812 Color (p (Red) (Green) (Blue) [Optional Led #, default 0] Colors in 8bit
  k	Set WS2812 Intensity (k <intensity 8bits>)
  l	Toggle MICS6814 Calibration Source. Preset/ADC mean since boot in 10 samples.
  x	Set MCP23017 pin. (x <1/0> [Pin# in port B] Default is Pin B1
  c	Toggle all MCP23017 Port B pins on/off.
  v	Set MPC23017 Port B Pin input or output. (v <1/0> [Port B pin. Default 1])
  b	Boot Specific Module Number. (b <module #>)
  n	Change first 3 WS2812 leds to Red, Green, Blue.
  d	Read VEML6070 sensor data. CRASHES ESP32. DONT KNOW WHY!
  z	Erases 23LC1024 RAM. CRASHES ESP32. DONT KNOW WHY!

  All other commands are ignored with an error message.

• TCA9548A Channels Used

  Rfiles • 08/28/2022 at 20:02 • 0 comments

  TCA9548 channels used:

  Channel	What is Connected
  0	MCP23017, ADS1115
  1	CCS811
  2	MPU9250, BMP280, TCS34725, VEML6075
  3	VEML6070
  4
  5
  6	SI7021, SI1145, MLX90614, BME280
  7	VL53L1

• MCP23017 pins USED

  Rfiles • 08/28/2022 at 20:01 • 0 comments

  MCP23017 Pins Used:

  PIN	What is Connected
  A0	TCS34725 Interrupt
  A1	ADS1115 Alarm
  A2	CCS811 Interrupt
  A3	VL53L1 GPIO1
  A4	SI1145 Interrupt
  A5	VEML6070 Ack
  A6	User Button Active Low
  B0	TCS34725 LED
  B1	User Red LED

• Modules Used in This Project

  Rfiles • 08/28/2022 at 20:00 • 0 comments

  Modules Used In This Project:

  HardWare	What I get
  BME280	Temperature, Pressure, Humidty
  ADS1115	4 channel 15 bit ADC. Channel 4 connected to 3.3V
  BH1750	Light Intensity
  BMP280	Temperature, Pressure
  CCS811	Equivalent CO2, Amount of Volatile Gases
  MCP23017	16 pin Input/Output Expander
  VL53L1	Laser Distance Sensor up to 4 meters
  VEML6070	UV intensity
  23LC1024	128kB External SPI RAM. Store Values. Pointless for now
  WS2812B	3 modules full RGB configurable LEDS
  MICS6814	3 Gases Sensor. Uses 3 channels of ADS1115. Measures 8 Gases
  MPU9250	9 Axis Montion Sensor. Accelerometer, Gyroscope, Magnetometer (3 axis each). Also chip temperature
  SI1145	Light and proximity sensor. Infrared, UltraViolet, Visible, Proximity (With white LED)
  VEML6075	Ultraviolet Sensor. UVa, UVb, UV intensity
  SI7021	Temperature, Humidity
  TCS34725	Light Sensor. Red, Green, Blue, Clear, IR, (LUX, K, CPL calculated)
  TCA9548A	I2C Switch and level translator for all I2C devices
  MLX90614	Infrared Temperature Sensor. Object Temperature, Ambient Temperature

  SoftWare	What I Get
  WiFi	WiFi
  INFLUX	Direct Connection to Database. DOESNT WORK
  MQTT	Send Data to Nodered in raspberry pi 3B+
  OTA	Auto check for Update in raspberry pi server, webpage server for update
  I2C Scanner	Scans TCA9548 for devices and lists in Serial Port

View all 6 project logs