Project Logs

Collapse

• Changes

  Richard Hogben • 06/13/2015 at 19:59 • 0 comments

  Current state:

  I've switched out the mic for better gain, and now have a small Neopixel ring for display.
  

  Updated sketch

  #include <Adafruit_NeoPixel.h>
  #include <avr/power.h>
  #include <Audio.h>
  #include <Wire.h>
  #include <SPI.h>
  #include <SD.h>
  
  #define PIN 5
  
  Adafruit_NeoPixel strip = Adafruit_NeoPixel(12, PIN, NEO_GRB + NEO_KHZ800);
  AudioInputAnalog         adc1;
  AudioAnalyzeFFT1024      myFFT;
  AudioConnection          patchCord1(adc1, 0, myFFT, 0);
  
  int dled = 13;
  
  void setup() {
    pinMode(dled, OUTPUT);
    AudioMemory(12);
    
    // Configure the window algorithm to use
    myFFT.windowFunction(AudioWindowHanning1024);
    
    strip.begin();
    strip.show(); // Initialize all pixels to 'off'
  }
  
  void loop() {
    float n;
    int i;
    int p;
  
    if (myFFT.available()) {
      // each time new FFT data is available
      for (i=0; i<strip.numPixels(); i++) {
        n = myFFT.read(i+5);
        if (n > 0.05) {
          p = (n+i)*1000;
          digitalWrite(dled, HIGH);
          strip.setPixelColor(i, Wheel(p));
          strip.show();
        }
      }
      digitalWrite(dled, LOW);
      colorWipe(strip.Color(0, 0, 0), 1);
    }
  }
  
  // Fill the dots one after the other with a color
  void colorWipe(uint32_t c, uint8_t wait) {
    for(uint16_t i=0; i<strip.numPixels(); i++) {
        strip.setPixelColor(i, c);
        strip.show();
        delay(wait);
    }
  }
  
  // Input a value 0 to 255 to get a color value.
  // The colours are a transition r - g - b - back to r.
  uint32_t Wheel(byte WheelPos) {
    WheelPos = 255 - WheelPos;
    if(WheelPos < 85) {
     return strip.Color(255 - WheelPos * 3, 0, WheelPos * 3);
    } else if(WheelPos < 170) {
      WheelPos -= 85;
     return strip.Color(0, WheelPos * 3, 255 - WheelPos * 3);
    } else {
     WheelPos -= 170;
     return strip.Color(WheelPos * 3, 255 - WheelPos * 3, 0);
    }
  }
  

  
  

• First Arduino sketch

  Richard Hogben • 06/06/2015 at 03:36 • 0 comments

  Mic is on pin 16 and LEDs are on PWM 23 and 22. The Teensy LED lights up for general frequency detection and the two LEDs light up and fade out at two higher frequencies.
  

  #include <Audio.h>
  #include <Wire.h>
  #include <SPI.h>
  #include <SD.h>
  
  AudioInputAnalog         adc1;
  AudioAnalyzeFFT1024      myFFT;
  AudioConnection          patchCord1(adc1, 0, myFFT, 0);
  
  int aledg = 23;
  int aledr = 22;
  int dled = 13;
  int brightness1 = 0;
  int brightness2 = 0;
  
  void setup() {
    pinMode(aledg, OUTPUT);
    pinMode(aledr, OUTPUT);
    pinMode(dled, OUTPUT);
    AudioMemory(12);
    
    // Configure the window algorithm to use
    myFFT.windowFunction(AudioWindowHanning1024);
  }
  
  void loop() {
    float n;
    int i;
  
    if (myFFT.available()) {
      // each time new FFT data is available
      for (i=4; i<175; i++) {
        n = myFFT.read(i);
        if (n >= 0.10) {
          digitalWrite(dled, HIGH);
        }
      }
      if ( myFFT.read(16) >= 0.10 ) {
        brightness1 = 255;
      }
      if ( myFFT.read(13) >= 0.10 ) {
        brightness2 = 255;
      }
      analogWrite(aledg, brightness1);
      analogWrite(aledr, brightness2);
      brightness1 = brightness1 -5;
      brightness2 = brightness2 -5;
      digitalWrite(dled, LOW);
    }
  }

View all 2 project logs