Close
0%
0%

STM32f103c8 board

Quick demo board made with Eagle and working with GCC G++ OpenCM3 Makefile FreeRTOS CAN

yangosoftyangosoft
Following
Liked Like project

Just one more thing

To make the experience fit your profile, pick a username and tell us what interests you.

Pick an awesome username
hackaday.io/
Your profile's URL: hackaday.io/username. Max 25 alphanumeric characters.
Pick a few interests
Projects that share your interests
People that share your interests

We found and based on your interests.

Choose more interests.

OK, I'm done! Skip
Similar projects worth following
3k views
3 comments
8 followers
View Gallery
Quick demo board made with Eagle and working with GCC G++ OpenCM3 Makefile FreeRTOS CAN

This project runs FreeRTOS 8.2.1 with OpenCM3 through STM32F103C8, a cheap ARM 32bits Cortex M3, in a custom board designed with Eagle 7.

Revision 10x10 v2 fixed. It works.

Updated FreeRTOS configuration.

  • 1 × stm32f103c8 Microprocessors, Microcontrollers, DSPs / ARM, RISC-Based Microcontrollers
  • 1 × USB to Serie

  • 10x8 v2

    yangosoft • 11/19/2015 at 07:52 • 0 comments

    I fixed some basic errors on the board:

    • Capacitors more close to the STM32
    • VBAT connected
    • VSSA connected to ground
    • VDDA connected to VCC

  • Layout 10x8

    yangosoft • 09/16/2015 at 06:41 • 0 comments

    I added a new layout 10cm x 8cm and sent it to a cheap Chinese PCB lab. I will upload some photos when receive it.

  • Revision 7. CAN USB changed

    yangosoft • 09/10/2015 at 12:15 • 0 comments

    • Removed UART pins
    • UART1 RX and TX are routed only in CH340G
    • CAN changed to alternative pins in order to avoid USB sharing
    • Added again ground planes

  • v5 layout

    yangosoft • 09/07/2015 at 15:37 • 0 comments

    • Revision 5 with better layout, pullup in USB+ and a CH340G.
    • Still missing a better solution with shared lines in CAN and programming USB.
    • Ground planes removed.

  • CH340G

    yangosoft • 07/30/2015 at 15:08 • 0 comments

    Added CH340G to UART1 for firmware burning through STM32F bootloader.

View all 5 project logs

  • 1
    Step 1

    Install ARM-GCC, makefile and stm32flash

    sudo apt-get install gcc-arm-none-eabi makefile stm32flash git
  • 2
    Step 2

    Clone repo:

    git clone https://github.com/yangosoft/stm32f103c8-board.git
  • 3
    Step 3

    Compile

    cd stm32f103c8-board/code/freertos_stm32f103
make

View all 4 instructions

Enjoy this project?

Share

Discussions

vapesforyou7 wrote 11/14/2023 at 17:11 • point

I have also make this but facing issue kindle check it out

https://gta-6.pro/gta-6-trailer/

  Are you sure? yes | no

K.C. Lee wrote 07/29/2015 at 15:14 • point

BTW I got the hardware side done here.  :)  https://hackaday.io/project/6607-stm32f103-canadian-maid-breakout-board

  Are you sure? yes | no

yangosoft wrote 07/30/2015 at 07:50 • point

¡That is a better board! And it's better routed.

  Are you sure? yes | no

Does this project spark your interest?

Become a member to follow this project and never miss any updates

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2025 Hackaday

Yes, delete it Cancel

Report project as inappropriate

You are about to report the project "STM32f103c8 board", please tell us the reason.

Send message

Your application has been submitted.

Remove Member

Are you sure you want to remove yourself as a member for this project?

Project owner will be notified upon removal.