Close
0%
0%

Julien

Software engineer making some electronics as an hobby

France
Following
Send a private message
Similar accounts worth following
30 Followers
17 Following
8 Projects
243 Likes
julien
Send a private message

This user joined on 06/20/2015.

20.5k
2.1k
34
137
ice40 FPGA based custom board to control eink display
Project Owner Contributor

FPGA eink controller

julienJulien

15.3k
55
0
35
Convert HDMI out from Rasperry Pi to scrapped LVDS panel with FPGA board
Project Owner Contributor

HDMI to LVDS panel converter

julienJulien

4.2k
37
3
21
This project use audio, SDRAM, SD card and USB of the STM32F746G-DISCO to provide an USB polyphonic SF2 MIDI synthesizer
Project Owner Contributor

STM32F746g Discovery SF2 MIDI synth

julienJulien

6.5k
230
19
13
MIDI synth board
Project Owner Contributor

Dream SAM2695 breakout board

julienJulien

1.7k
13
2
12
multi protocol interface tool
Project Owner Contributor

ifusb

julienJulien

1.5k
1.6k
1
11
MIDI autonomous music box
Project Owner Contributor

La boîte à musique

julienJulien

View all 8 projects

78.2k
102
15
79
Messing around with Annax Flip-Dot displays.
Project Owner Contributor

Flip-Dot Display & DIY Controller

frederic-lFrederic L

58.1k
575
35
405
An open hardware reading device rooted in Adafruit's Feather ecosystem
Project Owner Contributor

The Open Book Feather

joey-castillojoey castillo

57.7k
551
43
411
Experience freedom of communication without borders, operators, networks, fees !!! Create your own network, your own rules !!!
Project Owner Contributor

ARMACHAT - Doomsday wireless QWERTY communicator

bobriciusbobricius

48.4k
399
17
329
A mostly printed digital microscope powered by a Rasperry Pi Zero W
Project Owner Contributor

Pi Microscope

braunscncBraunsCNC

39.5k
360
27
332
A 252 electromagnet-matrix that controls Ferrofluid
Project Owner Contributor

Fetch: A Ferrofluid Display

applied-procrastinationApplied Procrastination

32.9k
412
27
324
An efficient and compact generator that can be coupled with wind turbines or water wheels to produce upwards of 100W
Project Owner Contributor

Portal Point Generator

vijayVijay

25.4k
146
43
135
I always wanted a large, affordable E-Ink screen to play around with. This board talks to cheap E-Reader replacement screens with an ESP32.
Project Owner Contributor

EPDiy: 9.7"/6" E-Paper controller

valentinValentin

16.1k
91
18
83
An all-in-one, made to hack step sequencer built around the Teensy platform with LiPo charging, touch TFT, encoders, buttons, and RGB leds.
Project Owner Contributor

Teensy Beats Shield

chris-millerChris Miller

14k
2.9k
18
51
LP3D is an (almost) fully lasercut, low component count 3D printer with all linear motion components cut directly into the frame.
Project Owner Contributor

LP3D: A fully lasercut kit 3D printer

luke-wallaceLuke Wallace

6.6k
60
16
60
Fast, small, available. Pick any three.
Project Owner Contributor

CP/M 50 Mk II

jessexmjessexm

6.6k
78
7
55
An open-source hiking, pilot, skiing, Signal-App-extending GPS mesh communicator.
Project Owner Contributor

Meshtastic

kevin-hesterKevin Hester

5.5k
49
9
46
Work in progress: Flow to synthesize VHDL/Verilog code into a PCB
Project Owner Contributor

VHDL/Verilog to Discrete Logic Flow

timTim

5.3k
58
0
38
Modular power generation system for powering and charging small electronic devices
Project Owner Contributor

Power Generation Modules

cole-bCole B

4.2k
36
12
33
A 40-key chocolate-bar mechanical keyboard.
Project Owner Contributor

Dorsch 40k Keyboard

dehipudeʃhipu

3.9k
30
1
22
Writing my own Gcode generator for pen plotter
Project Owner Contributor

Gcode Playground

mike-szczysMike Szczys

2.5k
2
2
2
Simple dummy load using wire wound resistors.
Project Owner Contributor

Resistive Load Tester DIY

robert-slgRobert Sälg

1.2k
10
1
9
Open and cheap DIY IP-KVM on Raspberry Pi with Mass Storage, Mouse, VNC and much more
Project Owner Contributor

Pi-KVM

mdevaevmdevaev

874
17
0
15
SAMD21 development board with LoRa radio module and GPS receiver, all programmable with the Arduino IDE
Project Owner Contributor

SAMD21 LoRa Development Board with GPS

nootropic-designnootropic design

View all

Share this profile

Share

Bits

Vittorio Loschiavo wrote 10/02/2018 at 05:37 • point

Hi Julien,

thanks for following my project https://hackaday.io/project/87345-mini-vertical-wind-generator-3d-printed

  Are you sure? yes | no

Afdhal Atiff Tan wrote 04/06/2017 at 16:48 • point

Thank you for following my battery balancer project :)

  Are you sure? yes | no

Patrick Van Oosterwijck wrote 01/30/2017 at 16:01 • point

Thank you for following my #LiFePO4wered/USB project! You might want to check out my #LiFePO4wered/18650 project for a bigger version as well.

  Are you sure? yes | no

Michel Kuenemann wrote 07/27/2016 at 15:25 • point

Bonjour, merci d'avoir mis un skull à mon projet Powerbucket. Cordialement Michel

  Are you sure? yes | no

Dave Vandenbout wrote 02/27/2016 at 18:28 • point

Thanks for following the CAT Board project!

  Are you sure? yes | no

Steve Smith wrote 08/20/2015 at 22:08 • point

Thanks for the Skull and Follow! :D

  Are you sure? yes | no

Eric Hertz wrote 06/28/2015 at 21:48 • point

Howdy! Thanks for the follow!

  Are you sure? yes | no

Send a private message to Julien

Become cool instantly

Create your Hackaday.io profile like Julien and many others

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday

Report user as inappropriate

You are about to report the user "Julien", please tell us the reason.