Close

Your browser (Internet Explorer) is out of date.

Update your browser for more security, comfort and the best experience on this site.

Update Internet Explorer'

Projects gustavoriverag likes and follows

17.1k
7.8k
69
A smart sensor Node to trigger an action on a smartphone each time a physical change is detected (temperature, displacement, click...)
Project Owner Contributor

Triggy - Sensor Node for Life Automation

vinchVinch

6.9k
6.6k
37
A computer built around a Atari 2600 (VCS), with a few nifty upgrades, 6502, 64k + 128bytes ram, coprocessor, 77 is getting a rework
Project Owner Contributor

Super atari 6502 (A "DIY" 2600 hardware clone...)

robertRobert

13.1k
5.9k
19
The 567 tone decoder is perhaps most famous Phase Locked Loop (PLL) chip. This project looks at an Arduino software PLL.
Project Owner Contributor

Software Phase Locked Loop

agpcooperagp.cooper

6.7k
5.9k
11
Connect all needed electronics to NodeMCU, add life to them with a help of programming, install HomeAssistant on PC and let's roll!
Project Owner Contributor

Home Automation With NodeMCU, HomeAssistant & MQTT

1barconnection1BarConnection

5.2k
5.4k
16
This projects converts a Bobby-Car (children's ride-on toy) to electric by using 4 Hoverboard motors, VESC controllers and an ESP32
Project Owner Contributor

Electric Bobby-Car

peter-ptziPeter Pötzi

5.9k
5.2k
10
ESP32 runs FabGL to produce VGA display
Project Owner Contributor

ESP32 VGA PS/2

land-boardscomland-boards.com

12.8k
4.5k
24
A 3D printed stereotax
Project Owner Contributor

3D printed rodent stereotaxic device

lex-kravitzLex Kravitz

97.2k
4.2k
633
A smaller and cheaper open source brushless motor
Project Owner Contributor

PCB Motor

carl-bugejaCarl Bugeja

3.6k
3.6k
31
Fully 3D Printed 6 DOF Arduino Robot Arm
Project Owner Contributor

LittleArm Big

slantconceptsslantconcepts

8.3k
3.2k
10
How I added a 500W heater to my 3D printer to enable reliable ABS printing.
Project Owner Contributor

Enclosure Heater for 3D Printer

mark-rehorstMark Rehorst

3.2k
3.2k
20
Adventures with an Ender 3
Project Owner Contributor

How to win at 3D printing

lion-mclionheadlion mclionhead

3k
3k
28
An open-source dual-channel SDR Raspberry Pi HAT with up to 6 GHz tunable range
Project Owner Contributor

CaribouLite SDR for RPI

david-michaeliDavid Michaeli

8.9k
2.8k
78
Two hearts are better than one, so why not have five. Quadcore RPI CM4 and a MCU on a single board for true all-in-one 3D printer control.
Project Owner Contributor

Sigmoid S7P 3D Printer Control Board

pkelectronicspkElectronics

11.6k
2.7k
54
No more restrictions from high level software! Access the lowest level of radio transmission with this programmable USB stick.
Project Owner Contributor

Open narrowband RF transceiver

samuel-kSamuel Žák

12.9k
2.4k
119
A functional 3D printable full body exoskeleton - Passive concept development
Project Owner Contributor

3X0 - 3D Printable exoskeleton concept

andrea-piccinnoAndrea Piccinno

2.4k
2.4k
7
Voice Controlled Personal Assistant robot to help you stay lazy using Raspberry Pi and Amazon Alexa
Project Owner Contributor

Dobby - DIY Voice Controlled Personal Assistant

dementorDementor

15.7k
2.2k
76
An Open Source Continuous Inkjet Printer
Project Owner Contributor

CIJ Printer

dominik-meffertDominik Meffert

2.5k
2k
19
Create a monitoring station to measure weather, soil, seismic, solar, magnetic, and gravity conditions - focus best accuracy/dollar w/COTS.
Project Owner Contributor

Climate & Environment Monitoring Station

sparksronsparks.ron

1.8k
1.8k
12
Game modifications for using haptic instead of visual senses
Project Owner Contributor

HapticGames

jantharJanThar

2k
1.6k
17
Citizen science project with mobile and fixed sensors for measuring air quality using low-cost sensors and smartphones
Project Owner Contributor

CanAir.io Air Quality Network

hpsaturnHpsaturn

4.2k
1k
5
A simple pocket-sized projector utilizing an Arduino
Project Owner Contributor

DIY Pocket Projector Design

sir-michael-iiSir Michael II

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2025 Hackaday