S-ROV : Underwater Drone
Already have an account? Log in.
To make the experience fit your profile, pick a username and tell us what interests you.
The most important thing in designing the ROV hardware was modularization for each part to make assembly and production easier. S-ROV consists of six parts, and each part can be made independently.
I'm still in the progress of designing and will continue to update the progress in this article. :)
In the previous ROV, the signal through the power line was connected to the computer via plc module. But it was so uncomfortable for me because I have to carry the laptop and connect it to plc module through ethernet cable..
In order to eliminate this inconvenience, I have configured a system to access the ROV wirelessly by attaching a small router to the PLC module as shown below.
I used Netis travel 2 router because it is very small and cheap!
Now, after we can access to ROV via smartphone, I applied the gamepad that can be attached to the smartphone to make the operation easier.(iPega 9023)
The problem I felt while watching the streamed video was the narrow viewing angle of the ordinary pi camera.
So, a few days ago, I got a Pi Camera (g) with a fish-eye lens and tested.
Below is a picture with fisheye lens.
When compared the image between normal camera and fisheye camera, I could see that the latter showed a mush larger viewing angle. But I could see the distortion caused by the spherical effect appears on the edge of image.. I think I need to think about whether there is any improvement in this part.
Finally, we have tested for the first time in a large water tank!
You can get more information from the following link :).
http://forum.bluesink.io/t/s-rov-first-test-in-water/27/2?u=dydwo92
Finally, we integrated the hardware and electrical devices and tested it in a small tank. We confirmed that the motors and LEDs work well, and the video streaming also works well! Tomorrow, we will go to a large water tank and conduct various tests :). However, the propellers will be shipped next week, so the drive test will be available next week.
I streamed the video from the camera attached to the ROV through 50m tether. You can find more information from the link below :)
http://forum.bluesink.io/t/video-streaming-using-mjpg-streamer/24?u=dydwo92
It's been updating in a long time :). In the meantime, there have been major electrical and hardware modifications. The control board has been redesigned to be more stable, and the front part of the main tube has been replaced with a hemispherical shape. I will replace the camera with a fisheye lens in the future. So it has been changed to hemisphere to make space. Detailed instructions about assembly and fabrication will be posted soon!
I have tested the waterproofing, and once I have confirmed that the water is not leaking. I'll test the waterproofing once again in a deeper water.
S-ROV Controller v.0.0
The following items have been revised and supplemented.
I will test it next week :)
github : https://github.com/BlueSink/Electronics-MainBoard
I have tested the main controller. The wiring is ,a bit complicated, but the following tests were conducted in the above situation.
1. PLC(Power Line Communication) availability
I checked the Ethernet communication through the 50m long wire and it works fine.
2. BLDC control
There are only two motors available at the moment, so I tested only two of them. To find out if a motor driver affects a sensitive part such as an MCU, I tried to input an excessive amount of motion, such as an excessive speed change in the motor, and it seemed to work well.
3. Additional PWM control
I tested several servo motors connected to the main board. There was no problem.
4. Complementary points
Here are some problems identified :
Finally I made the pcb! The main controller configuration is shown below, and I will test it as soon as possible. :)
I'm currently supplementing the design of the rov... It is not yet finalized, but as the specification becomes more and more definite, the design is being completed.
The cad files are open to Onshape.
I'm using Onshape. https://www.onshape.com/
It is Web-based CAD program. So you can use it without install software, and just sign in! Interface of it is similar to Solidworks. So if you are a Solidworks user, Onshape will also be easier to use.
YJ Kim
Fred Fourie
timonsku
Christoph Tack
Mile
Thanks Alot