Close
0%
0%

morph

IT guy into hobby electronics. Likes disassembling and re-purposing everything, often in the form of a radio.

Finland
Following
Send a private message
Similar accounts worth following
8 Followers
5 Following
3 Projects
46 Likes
morph
Send a private message

This user joined on 07/25/2014.

Proud member of

Jyväskylä Hacklab
4.8k
553
19
20
A minimalist direct conversion radio receiver. 4 general purpose transistors and a Polyakov 2 diode mixer.
Project Owner Contributor

PolyMorph Receiver

morphmorph

2.9k
326
0
19
A simple and tough cnc frame made from low cost hardware store parts and affordable electronics
Project Owner Contributor

The Peoples CNC Frame

morphmorph

953
10
2
7
Low power, low cost, low parts and low channel count USB talking LoRaWAN gateway (without concentrator) for OpenWRT routers and pals
Project Owner Contributor

Low Power LoRaWAN Gateway

morphmorph

1
0
A lake country hacklab in central Finland!
Project Owner Contributor

Jyväskylä Hacklab

morphmorph

51.4k
5.8k
30
194
FREE and Open Source, Arduino Due based Telescope Control GOTO
Project Owner Contributor

rDUINOScope Boiana

dessislav-gouzgounovDessislav Gouzgounov

43.3k
1.8k
82
503
RepRap HELIOS is a highly printable SCARA 3D printer. It has an outrageous print area and can print on almost any flat surface.
Project Owner Contributor

RepRap HELIOS

nicholas-sewardNicholas Seward

30.5k
467
51
152
Standalone Hardware Control Unit for use with "rDUINOScope" Firmware
Project Owner Contributor

GoTo Telescope Control for rDUINOScope

otto-winterOtto Winter

23.7k
5k
7
85
This project focuses on using building a budget powder bed 3d printer capable of printing bones, and creating the needed ink and powder.
Project Owner Contributor

Printing bones on a DIY powder bed 3d printer

jureJure

19.1k
109
5
56
My first self made CNC router!
Project Owner Contributor

DIY Multiplex Plywood CNC Router

hebel23hebel23

18.5k
48
5
35
A small and inexpensive kiln for melting metals and firing clay
Project Owner Contributor

RepKiln

matt-mosesMatt Moses

16.5k
917
4
71
This radio receiver is capable of receiving all MW and SW bandwidth, and can also operate as an SDR receiver, so with the help of PC and app
Project Owner Contributor

DIY SW , MW , Retro look Radio with ESP32/Si5351

mircemkmircemk

10k
2.1k
17
113
Sub 1GHZ RF wireless modules operating at 915MHZ and 433MHZ ISM bands, based on the ADF7023, full open source!
Project Owner Contributor

S1G RF: Sub 1GHZ Radio Modules 915MHZ and 433MHZ

avrAVR

10k
641
5
33
Transforming the humble 150x150x150mm stock print bed of a printrbot simple metal to a whopping 500x500x150mm
Project Owner Contributor

Printrbot 'SuperSize Me" Mod

kendoken.do

9.4k
103
6
71
The world's smallest fully automatic whiskey still built with safety as the foremost consideration.
Project Owner Contributor

The NanoStillery™ - Whiskey Distillery

capt-flatus-oflahertyCapt. Flatus O'Flaherty ☠

7.8k
1.3k
6
63
On its fourth revision, designed for heavy-duty use machining aluminum and possibly steel
Project Owner Contributor

Serious desktop CNC mill

dbtayldbtayl

7.8k
107
1
48
Growing food where it's needed, ready to be sold.
Project Owner Contributor

Modular Vertical Farming

alphaninjaalpha_ninja

5.3k
82
13
45
PIC32 DMA can send a sine table to a DAC at >3.2 million samples/sec, making low distortion 100 KHz sine waves and using zero cpu cycles.
Project Owner Contributor

ZERO CPU load function generator

bruce-landBruce Land

4.8k
20
5
13
This project is about converting a BUSMOUSE trackball to the USB HID protocol.
Project Owner Contributor

CH Products Trackball Pro USB modding

denis-guillaumeDENIS Guillaume

4k
997
11
71
A 3D model that can be sliced through a process called 'nesting', sent to a CNC Machine and constructed like a 3D Jigsaw puzzle.
Project Owner Contributor

TinyHackerHouse

anil-pattniAnil Pattni

3.8k
143
1
36
GPSDTx is a board capable of transmitting a signal up to a few MHz (1-3?) wide anywhere between 100MHz and 2.2GHz
Project Owner Contributor

General Purpose Software Defined Transmitter

brett-killionBrett Killion

2.8k
45
3
15
A simple bicycle computer that shows speed and distance on a LCD screen. It works on LiPo batteries and uses a reed switch as sensor.
Project Owner Contributor

Bicycle Computer

clovis-fritzenClovis Fritzen

1.2k
18
2
8
A reinterpretation on the CNC system to control a small garden, but using delta mechanics and fishing lines for large areas.
Project Owner Contributor

Delta Farmbot

tanahTanaH

View all

Share this profile

Share

Bits

Vishnu Mohanan wrote 03/28/2018 at 11:13 • point

Hey Morph, thanks for the follow :)

  Are you sure? yes | no

Fredrik Högberg wrote 03/27/2018 at 13:41 • point

Thank you for following my project # Lets make OSHW more successful! . We are searching for OSHW projects to collaborate with.

  Are you sure? yes | no

morph wrote 03/28/2018 at 09:23 • point

Collaboration sounds good, I'm thinking about making another larger 2x2m frame CNC machine. At the Jyväskylä Hacklab (https://jyvaskyla.hacklab.fi/en/) and in all the other Hacklabs in Finland we have many projects that are worthy of OSHW collaboration! Let me know if you are interested.

  Are you sure? yes | no

alpha_ninja wrote 05/24/2015 at 02:45 • point

Thanks for the follow!

  Are you sure? yes | no

hebel23 wrote 05/23/2015 at 20:25 • point

Thank you for the skull! Greetings from Germany. :o)

  Are you sure? yes | no

DENIS Guillaume wrote 05/23/2015 at 11:20 • point

Thanks a lot for the skull and the interest in my humble project.

  Are you sure? yes | no

Send a private message to morph

Become cool instantly

Create your Hackaday.io profile like morph and many others

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday

Report user as inappropriate

You are about to report the user "morph", please tell us the reason.