Close

Your browser (Internet Explorer) is out of date.

Update your browser for more security, comfort and the best experience on this site.

Update Internet Explorer'

Projects Harvey Sugar likes and follows

2.9k
1.9k
34
Bringing a vintage DIY binary counting computer back to life
Project Owner Contributor

Restoring the TRANSBINIAC computer

johnJohn

1.5k
1.4k
10
A really simple CAN network protocol for up to 30 nodes.
Project Owner Contributor

CAN Simple (protocol)

colinconstantcolinconstant

4.2k
880
23
For computer vision learners, drone and robot builders, AR/VR and 360 panorama experimenters. Open-source. Now with WiFi, BT, and more power
Project Owner Contributor

StereoPi v2 - CM4-based DIY stereoscopic camera

eugeneEugene

132.3k
348
256
Ground Penetrating Radar using Arduino
Project Owner Contributor

GPRino

mirel-paunMirel Paun

17.5k
125
89
Build a complete LW, MW and SW (AM and SSB) radio with the Si4735 / SI4732 and Arduino.
Project Owner Contributor

Si4735 SSB Receiver Controlled by Arduino

ricardo-lima-carattiRicardo Lima Caratti

12.8k
92
78
SOLO is a Motor Controller designed to easily run most types of electrical motors, DC, BLDC, PMSM and ACIM. it's easy to use and versatile.
Project Owner Contributor

SOLO, A Motor Controller for All Motors

miladmilad

7.9k
59
39
Cheap 3d printed hi torque robot actuator with electronics
Project Owner Contributor

Hi torque 3d printed cheap robot actuator

pavel-gPavel G.

9.8k
50
42
Look mum, no ADC!
Project Owner Contributor

FPGA + 3 R + 1 C = MW and SW SDR Receiver

alberto-garlassiAlberto Garlassi

4.6k
30
29
Using 36:1 Planetary Gear Actuator Module (2ea), 27:1 Planetary Gear Actuator Module (1ea) and 40:1 Cycloid Gear Actuator Module (3ea)
Project Owner Contributor

Low-Cost 3D Printed 6-DOF Manipulator

dongil-choiDongil Choi

5.5k
29
27
I needed a differential probe for BLDC motor ESC development and adapted Bud's design for my needs
Project Owner Contributor

A 1x, 100 MHz, 35 V common mode diff probe

christophChristoph

4k
28
24
Just a bionic hand optimized for 3D printing that costs less than $50)
Project Owner Contributor

DeltaBionics Rev0.1

anton-khrustalevAnton Khrustalev

3.2k
27
22
A "pod" containing fast pulse generator and sampler. This "pod" should serve as the basis of TDR-G3. The other part will be the main board.
Project Owner Contributor

TDR sampler/pulse generator "pod" (TDR-G3)

ms-bossMS-BOSS

4k
25
30
made only out of about 450 bipolar transistors (BC182)
Project Owner Contributor

Homebrew 4-bit transistorized CPU

gaborGabor

5.8k
24
37
A 6802 homebrew computer named PERSEUS-3 that was the basis of my PERSEUS series computers
Project Owner Contributor

PERSEUS-3 6802 homebrew computer

mitsuru-yamadaMitsuru Yamada

1.4k
21
23
Test arm for future 6 axis cobot arm.
Project Owner Contributor

3 AXIS compliant robot arm

petar-crnjakPetar Crnjak

2.8k
20
20
A 16-bit TTL CPU and stack machine built out of 7400-series chips.
Project Owner Contributor

TTL Operation Module (TOM-1)

tim-ryanTim Ryan

3.4k
15
15
Recreation of the MC14500-based WDR-1-Bit-Computer
Project Owner Contributor

WDR-1-Bit-Computer

pascalPascal

2.2k
15
17
A TTL CPU I built a long time ago when I bought a huge stock of NOS TTL chips on ebay
Project Owner Contributor

4 Bit TTL CPU

timTim

1.5k
13
15
16 bit VGA interface, 32K colors, graphic 640x480, sprites, sound, intended for Kobold K2 computer, no special video chips.
Project Owner Contributor

VGA video generation card

roelhroelh

5.1k
10
12
Experiments on optimizing discrete logic gates based on bipolar transistors
Project Owner Contributor

Evaluating Transistors for Bipolar Logic (RTL)

timTim

621
9
14
experiments with fast start-up oscillators
Project Owner Contributor

Gated Ring Oscillators

ted-yapoTed Yapo

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2025 Hackaday