Close
0%
0%

Louis

Hobbyist

Virginia
Following
Send a private message
Similar accounts worth following
1 Followers
31 Following
1 Projects
15 Likes
louis
Send a private message

This user joined on 07/19/2019.

772
12
4
15
Homebuilt 8-bit CPU and GPU for fun entertainment system.
Project Owner Contributor

j8ger

louisLouis

24.8k
2.5k
31
92
Underwater robots!
Project Owner Contributor

BorgCube ROV

tim-wilkinsonTim Wilkinson

23.1k
108
15
85
A 16 bit RISC computer with video display, from just a few TTL and memory chips. Online C compiler and simulator available.
Project Owner Contributor

Kobold K2 - RISC TTL Computer

roelhroelh

19.5k
2.4k
10
63
From raw RF samples of the GPS L1 C/A signal to a position fix, in a completely open fashion
Project Owner Contributor

Full Stack GPS Receiver

mike-hamster-fieldMike "Hamster" Field

15.8k
3.2k
26
145
A compact modular design of the strain wave gear for general robotic applications.
Project Owner Contributor

Compact Strain Wave Gear Actuator(s)

leo-vuLeo Vu

15.2k
2.4k
7
103
PlatformIO is an open source ecosystem for IoT development (Cross-platform IDE and unified debugger. Remote testing and firmware updates)
Project Owner Contributor

PlatformIO

ivan-kravetsIvan Kravets

12.4k
97
18
69
A home-brew 8 bit Microprocessor built on a breadboard 64K Address Space, IRQ, and DMA 16 Bit Stack Pointer, 4 8 bit Registers or 2 16 bit
Project Owner Contributor

8 Bit Breadboard CPU

2-zons2-Zons

9.7k
1.5k
5
24
Depth perception and obstacle detection glasses for the visually impaired using ultrasonic sensors and a binaural soundscape environment
Project Owner Contributor

SonicScape (Binaural Sensor Glasses for the Blind)

pawit-kochakarnPawit Kochakarn

8.7k
2.4k
0
37
Put your Verilog on real hardware, real cheap
Project Owner Contributor

FPGA Bootcamp #3

al-williamsAl Williams

7.7k
2.3k
2
5
This tutorial will show you how to configure volumio to support HIFI DAC.
Project Owner Contributor

How to configure volumio to support HIFI DAC.

ameliayouamelia.you

7.2k
1.5k
1
38
Universal 3D printed gripper for robotics.
Project Owner Contributor

Modular Universal Jamming Gripper

cole-bCole B

6.6k
2k
8
51
An Arduino clone based on a TI's Tiva TM4C123G (An 80Mhz ARM M4F with USB OTG)
Project Owner Contributor

Roadrunner (the Arduino-Tiva)

jacobJacob

5.3k
5.9k
5
12
Low cost IoT platform for Arduino Nano and Raspberry Pi under 9USD for all parts (included shipping) base on Ebay seller.
Project Owner Contributor

Low cost (~ 9$) IoT for Arduino and Raspberry Pi

simonSimon

4.3k
687
0
44
Photovoltaic, Thermoelectric, Piezoelectric, Magnetic induction Energy scavenger
Project Owner Contributor

PTPM Energy Scavenger

mileMile

3.8k
3.8k
1
4
Audi Dynamic Turn Signal
Project Owner Contributor

Audi Dynamic Turn Signal

arekArek

3.2k
3.2k
1
11
A first attempt for a small, attractive and practical soldering station, a project designed not by the cost but rather the experimentation.
Project Owner Contributor

AVR Soldering Iron

manosManos

1.7k
587
0
9
Using the 8BitRobots Module to operate a 3D printed robot arm
Project Owner Contributor

3D Printed Robot Arm: 8BitRobots

tim-wilkinsonTim Wilkinson

1.5k
128
2
25
An m68k homebrew with an FPGA acting as a VGA graphics controller
Project Owner Contributor

Diapason : m68k homebrew with FPGA graphics

carson-herringtonCarson Herrington

1.4k
1.8k
0
4
Build a portable Pi laptop with built in breadboard space and solar charging.
Project Owner Contributor

Travelling Pi Laptop

ted-vartyTed Varty

View all

Share this profile

Share

Bits

Dusan Petrovic wrote 03/06/2020 at 15:03 • point

Hi @Louis, thank you for following my #Homebrew CPU list.

  Are you sure? yes | no

Send a private message to Louis

Become cool instantly

Create your Hackaday.io profile like Louis and many others

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday

Report user as inappropriate

You are about to report the user "Louis", please tell us the reason.